. Contents Package Contents.Introduction.Using Your Computer.1.Main Unit Setup.6 1. Initiation of Main Unit 2. Basic Display Modes 2. Overview of Button Operation.
In Data Setting Mode 2. In General Mode 3. In Altitude Calibration Mode 3.
Package Contents 1. MAIN UNIT Main unit 3V battery (CR2032) 2. BRACKET SET Bracket for handlebar or stem Bracket base Twin adhesive tape Cable ties 3. SPEED TRANSMITTER SET Speed transmitter 3V battery (CR2032) Transmitter rubber pad Cable ties Magnet set O-ring 4. Introduction Congratulations on having chosen the cycle computer with altimeter functions from ECHOWELL. The easy operation of your new Echo-a1 or Echo-a2 will let you enjoy much fun from riding. Please read this manual carefully before using the device to get familiar with the operation logic.
There is a highly sensitive pressure sensor inside each Echo-a1 or Echo-a2 cycle computer, and there is a hole at the bottom of each main unit for measuring the pressure. You should always keep the hole clean to avoid incorrect measurement and must not poke a needle or any pointed article into it to avoid damage. Using Your Computer 1.Main Unit Setup 1. Initiation of Main Unit: 1. Before normal operation, initiate the main unit and select units as stated below: 1-1.
User Guide
Push buttons A, B, C simultaneously for 3 seconds, and you'll see the auto-testing display. The following is the General Mode Display during riding for reference. Overview of Button Operation This computer includes three major display modes as shown below: Data Setting Mode, General Mode, and Altitude Calibration Mode. In this section, you'll learn the function of each button in each mode. The following text lets you know how to use the buttons to operate the computer step by step. In General Mode, press the C button to enter Data Setting Mode. 2.In Data Setting Mode, press the C button to exit and return to General Mode.
Button D: No function. How do you enter Data Setting Mode after initiating the computer? After initiating the computer by pressing the A, B, C buttons at the same time for 3 seconds, press any button to quit auto-testing display, and then select units. Altitude Calibration Mode.
Button D: Press the D button to switch to Bike 1 or Bike 2. In Altitude Calibration Mode Tips: 1.The buttons you'll use in Altitude Calibration Mode: A, B. 2.Buttons for entering or quitting Altitude Calibration Mode: A+B (3's) 3.Buttons for quickly resetting the current altitude to zero: A+B (1's) Buttons A+B: 1. Wheel Circumference Measurement To set the wheel circumference before riding, you should measure the wheel circumference by yourself or just refer to the Wheel Circumference Table as shown below. How do you measure the wheel circumference yourself?
Scott Stars: Bridget Moynahan, Common, David Patrick Kelly, Ian McShane, John Leguizamo, Keanu Reeves, Lance Reddick, Laurence Fishburne, Riccardo Scamarcio, Thomas Sadoski Imdb: 7.9/10 Sinopsis John Wick Chapter 2 (2017) BluRay ini merupakan film yang bercerita tentang kisah kelanjutan dari film sebelumnya yang berjudul ‘John Wick’ yang tayang pada 2014 lalu. Jangan lupa like fanspage kami join grup fb kani di bila diperlukan pasword: filmbluray360p.com atau bluraydrive.us Genre: Action, Crime, Thriller Sutradara: Chad Stahelski, Leslie Zak, Shane B. John wick blu-ray release. Di film ini, kembalinya John Wick ( Keanu Reeves ) yang merupakan seorang pembunuh bayaran legendaris setelah dari pensiunnya, kini John Wick memiliki misi dan berada di tempat paling berbahaya di kota Roma, Italia yang terdapat banyak mafia gangster.
Roll the wheel until the valve stem is closest to the ground and mark the corresponding spot on the floor as the first point. Next, roll the wheel forward until the valve stem is closest to the ground once again. Mark the corresponding spot on the floor as the second point.
Basic Setting & Operation Tip for Data Setting: 1. Press the A button to change the value of a flickering digit. Press the B button to move to the next digit in a loop. Press and hold the B button for 1 second to move to the next setting when the current setting is finished. General Display The display of General Mode looks different in different phrases as shown below: 1. Put the main unit onto the bracket, and the main unit will automatically start measuring the speed and cadence.
The main unit will automatically enter Sleep Mode in 15 minutes once it doesn't receive any signals from the bike. Battery Replacement 1. When the low battery indicator is shown on the display, replace the battery with a new one A.S.A.P.
The positive (+) pole of the CR2032 battery must face the battery cap. 3.Press buttons A, B, C for 3 seconds to initiate the main unit. Attention: When there's the low battery symbol on the screen, we suggest that you replace the battery with a new one A.S.A.P. General Mode Display When you are riding with the computer, some functions will not be displayed on the screen.
These functions like T.AL, ODO, mBAR, DST/D are displayed only when you stop riding. About Altitude Calibration: Tip for Quick Altitude Calibration 1. Press both A and B buttons for 1 second, and the current altitude value will return to zero. Press the A button to set the value of a digit, and press the B button to move to the next digit. Temperature Display Echo-a2 only: The following operation is for 10.
Bike 1 /Bike 2 Selection Bike 1 and Bike 2 have their separate data in the computer. Data Reset 1.
Press and hold the A button for 3 seconds to reset data of DST, RTM, MAX, AVG, ALT,MAX-ALT, MAX-RPM, AVG-RPM (for Echo-a2 only) 2. The following data are stored in memory and cannot be reset: Unit, Cmm1 (Circumference 1), Cmm2, ODO 1, ODO 2, T.RT1, T.RT2, T.AL1, T.AL2. EL Backlight 13. Sleep Mode Press the A or B button to wake it up. Functions The display of the computer can be divided into three sections – upper, middle, and lower display. In General Mode, the LCD display of your computer is as below: The current altitude is always shown on the upper display, and it's easy to calibrate it when necessary. For Bike 2, when you do not ride the bike for more than 2 seconds, the speed data will be reset to zero.
With this function, the computer will record the maximum speed you reach during riding. wheel signals. If you are riding your Bike 2, the computer will count the riding time for 2 more seconds for the same reason.
Regarding the riding time it over counts, the computer will automatically deduct it and show the correct riding time. RPM Current Cadence (for Echo-a2 only) 1. ALT Accumulated Altitude Gains (During a Trip) 1.
With this function, it displays the accumulated altitude gains during a trip. When you ride over uphill paths, the altimeter will accumulate the altitude gains. However, when you ride over downhill paths, the computer will not deduct the altitude loss. The altimeter converts the millibar value of atmospheric pressure into the current altitude. Attention: There is a hole at the bottom of the main unit for measuring the air pressure.
The hole for measurement should be always kept clean. Besides, do not poke anything into the hole to avoid damage. T.AL Total Accumulated Altitude Gains 1. It displays the total accumulated altitude gains during all previous trips.
The accumulated altitude gains cannot be cleared by the reset operation. T.AL (1)+(2) Total Accumulated Altitude Gains (Bike 1 + Bike 2) 1. Low Battery Indicator 1. When the low-battery indicator appears on the display, it's time to get a new battery. Replace the battery with a new one A.S.A.P. When the symbol blinks on the display.
Otherwise, the new data of some functions will not be stored into the computer. Distance Per Day 0-999.99 km/mile Riding Time for Bike 1 0H:00M:00S-99H:59M:59S Riding Time for Bike 2 0H:00M:00S-99H:59M:59S Total Riding Time for Bike 1 0H:00M:-9999H:59M Total Riding Time for Bike 2 0H:00M:-9999H:59M Total Riding Time (Bike 1 + 0H:00M-19999H:59M Bike 2) -500m - 8000m Current Altitude (-1640ft - 26240ft) UNIT:1m/3ft. Circumference for Bike 1 0-3999mm (default: 2155mm) Circumference for Bike 2 0-3999mm (default: 2050mm) 1H:00M:00S-12H:59M:59S, 12/24H Clock 0H:00M:00S-23H:59M:59S Automatically shifted to the next Auto-Scan per 5 seconds Low Battery Indicator Light for 3 seconds after each EL Back-light press LCD Brightness Levels 1 - 4. The following RPM (cadence) functions are for Echo-a2 only: Current RPM. General Specifications Operating Temperature C - 50 C (32 F - 122 ° ° ° ° Storage Temperature: C - 60 C (14 F - 140 ° ° ° ° Sensor & Transmitter: No-contact magnet sensor with wireless transmitter Suitable Fork Sizes: 12 mm - 50 mm (0.5'. Precautions 1. Watch the road.
Don't pay much attention to your cycle computer functions during riding to avoid accidents. Don't expose the main unit to direct sunlight for a long time while you're not riding with it.
Never disassemble the device or the accessories. Trouble Shooting Check the Problem Solutions following: No display 1.Is the battery dead? 1.Replace the battery with a 2.Is the battery new one.
Installation correct? 2.Make sure the positive pole of the battery faces the battery cap. Speed not 1.Is the computer in the 1.
LCD is Did you expose the Put the main unit in the shade black. Main unit to the direct to let it return to normal state. Sunlight for a long time when it was not in use? Display is Is the temperature The computer will return to slow.
Mount the SENSOR with 2 cable ties on the front fork with the RUBBER PAD, and let the sensor face the spoke, do not tighten the cable ties before the sensor is placed in the right position. B0) on one spoke of the front wheel and let the magnet face the sensing zones. Attach the BRACKET to the handlebar and fit the RUBBER PAD between the handlebar and the band of the bracket. It can lock up the main unit, ensuring that the main unit will not drop out while riding. Make sure the sensor cable is loose enough for the handlebar to turn freely before tightening the cable ties.
Secure excess wire near the fork crown by wrapping it around the front brake cable or by bending it back and forth and securing it with cable ties. Mount the main unit onto the bracket by sliding it from front to rear till it clicks into position. To remove the main unit, press down on the lock lever of the bracket then pull the main unit forward and off. The computer can stand on the desk and act as a normal clock when you bring it indoors. Replace battery with a new one within 2 weeks after the symbol was appeared, otherwise incorrect data may be display when the battery voltage is too low. Replace with a new LR44 (cross reference type A76, AG13 or V13GA) computer with the positive (+) pole toward the battery cap. This computer can be used in the rain but should not be used under water.
01 Km or Miles 0-99999Km or Miles 1 Km or Miles 0:00'00'- 9:59' 59' 1 Second 0:00' 12:59' 1 Minute Remark: All functions data are updated once a second. (The original factory-attached battery may be shorter than this period due to shipping and storage time. DISCLAIMER TO DOWNLOAD THE USER GUIDE ECHOWELL ZONE-7. Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software: user guide, owner's manual, quick start guide, technical datasheets. In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description.
Lastmanuals, for instance, does not offer a translation service. Click on 'Download the user Manual' at the end of this Contract if you accept its terms, the downloading of the manual ECHOWELL ZONE-7 will begin.
Ask a question about the Echowell Eon-11w Have a question about the Echowell Eon-11w but cannot find the answer in the user manual? Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Echowell Eon-11w. Please make sure that you describe your difficulty with the Echowell Eon-11w as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question.
Calibration 1. Setting Km/H or Mile/H A) Press the button on bottom of computer for 6 seconds to start setup. B) Hold the button until the flickering digit is changed to the digit “2” of the C2155 to recognize either Km/H or Mile/H as desired. Setting the wheel circumference C mm A) The default is set at 2155mm. Measure the value for your wheel. B) A quick press of the button advances the flickering digit by 1.
C) To change the flickering digit, hold down the button until the flickering digit moves to the next digit. D) Hold down the button until (about 6 seconds) it jumps out the setting to store the desired data and complete setup. Wheel circumference A) Precise measurement: Roll wheel 1 revolution, measure the distance from the marked first point and the second point. B) Measure the Wheel Radius R Cmm = 6.2832 x R (R in mm) Cmm = 159.60 x R (R in inches) (1 inch = 25.4mm).The above mentioned instruction as calibrating the cycle computer is available for most of the Echowell’s computers, but NOT for each model. Please contact us if you have problem in re-calibration.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |